Industrial safety

Safety management software: what it does, and where camera detection fits

What safety software covers, what to check before buying, and where your cameras fit.

  • Runs on existing IP cameras (RTSP/ONVIF) Camera fitness confirmed by a survey
  • Licensed per camera stream, every use included SquintPRO, built and supported by Interkey
  • On-premise or cloud No face recognition

Teams we work with on SquintPRO

Safety management software records incidents, near misses, inspections, permits and corrective actions in one place, so a safety team can see trends and close actions. It depends on people reporting what they see. Camera-based detection adds a second source: it logs events such as missing protective equipment automatically, with a clip, around the clock.

The modules of safety management software

Seven modules most safety management software carries, and what each one records
ModuleWhat it records
IncidentsEvents that caused injury, damage or loss, the investigation that follows, and the type of work injury
Near missesEach near miss that could have caused harm and did not, with its place, time and cause
InspectionsPlanned checks against a list, what was found and a photo of each finding, a daily task of the safety officer
PermitsHigh-risk work: who asked, who approved, the isolations and when it closed. See how a permit to work runs
Risk assessmentThe hazards of each task or area, their rating and the agreed controls, as our risk assessment guide sets out
Corrective actionsEvery action raised by an incident, inspection or audit, with an owner, a due date and a status until it closes; closing on time is one of the safety KPIs
TrainingWho completed which course, when it must be renewed, and the record of each toolbox talk

Most products sell these as separate modules, and few sites need all seven on the first day.

From report to action

  1. Sources of reports

    People on site Cameras
  2. Safety management software

    One record per event: what happened, where, when, and who owns the follow-up

  3. Actions

    Investigations, corrective actions with an owner and a date, and trend reports

Reports from people and detections from cameras arrive in one system, which turns them into actions.

Eight things to check before you buy

Ask each supplier to show these in a live demo with your own examples, not on slides.

  • Arabic in the interface and the reports. Forms, alerts and printed reports in Arabic, right to left, not translated labels on an English screen.
  • Working offline. A report made where there is no signal is saved on the phone and sent later.
  • A mobile app. Workers report from their own phone, with a photo, in a few taps.
  • Where the data is kept. Your data centre or a cloud region your policy accepts. Ask before the demo.
  • Integration. An interface (API) or import for the staff list, equipment records and camera detections.
  • Easy reporting. A near miss that is slow to report is usually not reported. Count the taps.
  • Reports for management and clients. The periodic reports they ask for, produced by the system, not rebuilt in a spreadsheet each month.
  • Local support. Help in Arabic from inside the Kingdom, from people who can change a form when your procedure changes.

The reporting gap

Safety management software only knows what someone types into it. The incident register is usually close to complete, because an injury is hard to miss; the near-miss register stays thin. A worker who stepped back from a reversing truck carries on with the shift: nobody was hurt, the form takes time, and nobody asked. Unsafe conditions seen at night are often fixed on the spot and never written down.

The result is a system full of outcomes and short of warnings. Our near-miss guide covers the reporting habits that help; the next section looks at a second source.

Where camera detection fits

Camera-based detection adds a source that does not wait for someone to decide to report. SquintPRO, the computer vision platform Interkey builds, detects missing protective equipment, people too close to forklifts and moving equipment, smoke and fire, and entry into restricted areas. Each detection carries a clip, the time, the camera and the zone, and reaches your team as an alert in the workflow it already uses. It runs on premise or in the cloud, and it does not recognise faces.

SquintPRO works on the IP cameras you already have, over RTSP or ONVIF. Interkey does not supply or install cameras. A common first case is PPE detection on existing CCTV.

What SquintPRO is not

Not a safety management system

SquintPRO is not a safety management system: it does not manage permits, training, inspections or corrective actions, and it does not replace the software your team reports into. It sends the alert and the clip; how it connects to your system is agreed in the project.

From records to indicators

Incidents, injuries and lost days are lagging indicators: they count harm already done. Inspections completed, near misses reported and actions closed on time are leading indicators: they show whether preventive work is being done. Our page on leading and lagging safety indicators explains both.

Leading indicators are only as good as the reports behind them: a month with few near misses can mean a safer site or a quieter reporting habit, and the software cannot tell which. A second source, recorded the same way on every shift, makes the trend easier to read.

How to choose and start

Each step builds on the one before it.

  1. List what you record today.

    The paper forms and spreadsheets in use, who fills them in and who reads them.

  2. Shortlist against the eight checks.

    Ask each supplier to run your own near miss and permit, in Arabic, on a phone.

  3. Start on one site.

    Begin with incidents, near misses and corrective actions; add the rest once people report in the new system.

  4. Add the second source.

    Then add camera detections as observations. A pilot with a defined scope on one site shows what your cameras add.

Questions about safety management software

What is safety management software?

Safety management software records incidents, near misses, inspections, permits and corrective actions in one place, so a safety team can see trends and close actions. It replaces paper forms and spreadsheets with one record per event and an owner for each follow-up. Most products are sold in modules, so a site can start small.

What is the difference between EHS and HSE software?

There is no real difference: both names describe the same kind of software, with the letters in a different order. Products sold as EHS software often add environmental records such as waste and emissions, and HSE is the more common name on Gulf sites. Our glossary explains EHS and HSE as terms.

Can cameras feed a safety management system?

Yes, as an automatic source of observations. Camera-based detection sends the event, a clip, the time and the place, so the record no longer depends on someone choosing to report it. How a detection reaches your system is agreed in the project, once the system you use and the interfaces it offers are known.

Is SquintPRO a safety management system?

No. SquintPRO is a camera-based detection platform that works beside your safety management system, not in its place. It watches existing IP cameras for conditions such as missing protective equipment or entry into restricted areas, and sends an alert with a clip. Permits, training, inspections and corrective actions stay in the software your team already uses.

What should a Saudi site check first?

Check Arabic first, then where the data is kept. The interface, the mobile app and the printed reports should work in Arabic, right to left, for the people who report on site. Then confirm whether the data stays in your data centre or in a cloud region your policy accepts, before the demo.

Next step

Scope a pilot, or ask one question

Tell us about one site, the cameras it has and how you record safety events today.

Required field

By sending this form, you agree to our Privacy Notice.

What happens next

  1. We read your request
  2. An engineer contacts you
  3. You get an estimate or a demo

Or directly

+966-11-2180999 [email protected]

Tawuniya Towers, North Tower, 7th Floor, King Fahad Highway, Olaya, P.O. Box 56835, Riyadh 11564, Saudi Arabia

or Industrial safety monitoring

Published by Interkey. Last updated . Interkey is registered in Riyadh, Saudi Arabia under commercial registration 1010156897.